diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 4fa07c0871..5ada0d3293 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -67,7 +67,7 @@ // Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD - #define MOTHERBOARD BOARD_RAMPS_14_EFB + #define MOTHERBOARD BOARD_BTT_SKR_MINI_E3_V2_0 #endif /** @@ -78,7 +78,7 @@ * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ -#define SERIAL_PORT 0 +#define SERIAL_PORT 2 /** * Serial Port Baud Rate @@ -91,7 +91,7 @@ * * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] */ -#define BAUDRATE 250000 +#define BAUDRATE 115200 //#define BAUD_RATE_GCODE // Enable G-code M575 to set the baud rate @@ -100,7 +100,7 @@ * Currently Ethernet (-2) is only supported on Teensy 4.1 boards. * :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7] */ -//#define SERIAL_PORT_2 -1 +#define SERIAL_PORT_2 -1 //#define BAUDRATE_2 250000 // :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] Enable to override BAUDRATE /** @@ -115,7 +115,7 @@ //#define BLUETOOTH // Name displayed in the LCD "Ready" message and Info menu -//#define CUSTOM_MACHINE_NAME "3D Printer" +#define CUSTOM_MACHINE_NAME "Build 011" // Printer's unique ID, used by some programs to differentiate between machines. // Choose your own or use a service like https://www.uuidgenerator.net/version4 @@ -138,9 +138,9 @@ * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] */ -#define X_DRIVER_TYPE A4988 -#define Y_DRIVER_TYPE A4988 -#define Z_DRIVER_TYPE A4988 +#define X_DRIVER_TYPE TMC2209 +#define Y_DRIVER_TYPE TMC2209 +#define Z_DRIVER_TYPE TMC2209 //#define X2_DRIVER_TYPE A4988 //#define Y2_DRIVER_TYPE A4988 //#define Z2_DRIVER_TYPE A4988 @@ -152,7 +152,7 @@ //#define U_DRIVER_TYPE A4988 //#define V_DRIVER_TYPE A4988 //#define W_DRIVER_TYPE A4988 -#define E0_DRIVER_TYPE A4988 +#define E0_DRIVER_TYPE TMC2209 //#define E1_DRIVER_TYPE A4988 //#define E2_DRIVER_TYPE A4988 //#define E3_DRIVER_TYPE A4988 @@ -533,7 +533,7 @@ #define TEMP_SENSOR_5 0 #define TEMP_SENSOR_6 0 #define TEMP_SENSOR_7 0 -#define TEMP_SENSOR_BED 0 +#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_PROBE 0 #define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_COOLER 0 @@ -616,7 +616,7 @@ #define HEATER_5_MAXTEMP 275 #define HEATER_6_MAXTEMP 275 #define HEATER_7_MAXTEMP 275 -#define BED_MAXTEMP 150 +#define BED_MAXTEMP 125 #define CHAMBER_MAXTEMP 60 /** @@ -656,9 +656,9 @@ #define DEFAULT_Ki_LIST { 1.08, 1.08 } #define DEFAULT_Kd_LIST { 114.00, 114.00 } #else - #define DEFAULT_Kp 22.20 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114.00 + #define DEFAULT_Kp 21.73 + #define DEFAULT_Ki 1.54 + #define DEFAULT_Kd 76.55 #endif #endif @@ -1215,14 +1215,14 @@ * Override with M92 * X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]] */ -#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 500 } +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 93 } /** * Default Max Feed Rate (linear=mm/s, rotational=°/s) * Override with M203 * X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]] */ -#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } +#define DEFAULT_MAX_FEEDRATE { 500, 500, 20, 120 } //#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2 #if ENABLED(LIMITED_MAX_FR_EDITING) @@ -1250,9 +1250,9 @@ * M204 R Retract Acceleration * M204 T Travel Acceleration */ -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves +#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves /** * Default Jerk limits (mm/s) @@ -1262,7 +1262,7 @@ * When changing speed and direction, if the difference is less than the * value set here, it may happen instantaneously. */ -//#define CLASSIC_JERK +#define CLASSIC_JERK #if ENABLED(CLASSIC_JERK) #define DEFAULT_XJERK 10.0 #define DEFAULT_YJERK 10.0 @@ -1274,7 +1274,7 @@ //#define DEFAULT_VJERK 0.3 //#define DEFAULT_WJERK 0.3 - //#define TRAVEL_EXTRA_XYJERK 0.0 // Additional jerk allowance for all travel moves + #define TRAVEL_EXTRA_XYJERK 5.0 // Additional jerk allowance for all travel moves //#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2 #if ENABLED(LIMITED_JERK_EDITING) @@ -1381,7 +1381,7 @@ /** * The BLTouch probe uses a Hall effect sensor and emulates a servo. */ -//#define BLTOUCH +#define BLTOUCH /** * MagLev V4 probe by MDD @@ -1461,6 +1461,9 @@ */ //#define SENSORLESS_PROBING +// Not doing sensorless probing, so disable the warning about diag(nostic?) jumpers. +#define DIAG_JUMPERS_REMOVED + /** * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe * Deploys by touching z-axis belt. Retracts by pushing the probe down. @@ -1533,7 +1536,7 @@ * | [-] | * O-- FRONT --+ */ -#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 } +#define NOZZLE_TO_PROBE_OFFSET { -40, -10, 0 } //DCMINTER // Enable and set to use a specific tool for probing. Disable to allow any tool. #define PROBING_TOOL 0 @@ -1621,14 +1624,14 @@ #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes //#define Z_AFTER_PROBING 5 // Z position after probing is done -#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping +#define Z_PROBE_LOW_POINT -5 // Farthest distance below the trigger-point to go before stopping // For M851 give a range for adjusting the Z probe offset #define Z_PROBE_OFFSET_RANGE_MIN -20 #define Z_PROBE_OFFSET_RANGE_MAX 20 // Enable the M48 repeatability test to test probe accuracy -//#define Z_MIN_PROBE_REPEATABILITY_TEST +#define Z_MIN_PROBE_REPEATABILITY_TEST // Before deploy/stow pause for user confirmation //#define PAUSE_BEFORE_DEPLOY_STOW @@ -1696,7 +1699,7 @@ // @section motion // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. -#define INVERT_X_DIR false +#define INVERT_X_DIR true #define INVERT_Y_DIR true #define INVERT_Z_DIR false //#define INVERT_I_DIR false @@ -1709,7 +1712,7 @@ // @section extruder // For direct drive extruder v9 set to true, for geared extruder set to false. -#define INVERT_E0_DIR false +#define INVERT_E0_DIR true #define INVERT_E1_DIR false #define INVERT_E2_DIR false #define INVERT_E3_DIR false @@ -1750,8 +1753,8 @@ // @section geometry // The size of the printable area -#define X_BED_SIZE 200 -#define Y_BED_SIZE 200 +#define X_BED_SIZE 410 +#define Y_BED_SIZE 410 // Travel limits (linear=mm, rotational=°) after homing, corresponding to endstop positions. #define X_MIN_POS 0 @@ -1759,7 +1762,7 @@ #define Z_MIN_POS 0 #define X_MAX_POS X_BED_SIZE #define Y_MAX_POS Y_BED_SIZE -#define Z_MAX_POS 200 +#define Z_MAX_POS 250 //#define I_MIN_POS 0 //#define I_MAX_POS 50 //#define J_MIN_POS 0 @@ -1970,7 +1973,7 @@ */ //#define AUTO_BED_LEVELING_3POINT //#define AUTO_BED_LEVELING_LINEAR -//#define AUTO_BED_LEVELING_BILINEAR +#define AUTO_BED_LEVELING_BILINEAR //#define AUTO_BED_LEVELING_UBL //#define MESH_BED_LEVELING @@ -1985,7 +1988,7 @@ /** * Auto-leveling needs preheating */ -//#define PREHEAT_BEFORE_LEVELING +#define PREHEAT_BEFORE_LEVELING #if ENABLED(PREHEAT_BEFORE_LEVELING) #define LEVELING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time #define LEVELING_BED_TEMP 50 @@ -2005,7 +2008,7 @@ * Turn on with the command 'M111 S32'. * NOTE: Requires a lot of PROGMEM! */ -//#define DEBUG_LEVELING_FEATURE +#define DEBUG_LEVELING_FEATURE #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL, PROBE_MANUALLY) // Set a height for the start of manual adjustment @@ -2034,7 +2037,7 @@ /** * Enable the G26 Mesh Validation Pattern tool. */ - //#define G26_MESH_VALIDATION + #define G26_MESH_VALIDATION #if ENABLED(G26_MESH_VALIDATION) #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for G26. @@ -2050,7 +2053,7 @@ #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) // Set the number of grid points per dimension. - #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_X 5 #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X // Probe along the Y axis, advancing X after each column @@ -2060,13 +2063,13 @@ // Beyond the probed grid, continue the implied tilt? // Default is to maintain the height of the nearest edge. - //#define EXTRAPOLATE_BEYOND_GRID + #define EXTRAPOLATE_BEYOND_GRID // // Subdivision of the grid by Catmull-Rom method. // Synthesizes intermediate points to produce a more detailed mesh. // - //#define ABL_BILINEAR_SUBDIVISION + #define ABL_BILINEAR_SUBDIVISION #if ENABLED(ABL_BILINEAR_SUBDIVISION) // Number of subdivisions between probe points #define BILINEAR_SUBDIVISIONS 3 @@ -2145,7 +2148,7 @@ #endif // Add a menu item to move between bed corners for manual bed adjustment -//#define LCD_BED_TRAMMING +#define LCD_BED_TRAMMING #if ENABLED(LCD_BED_TRAMMING) #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets @@ -2209,7 +2212,7 @@ * - Allows Z homing only when XY positions are known and trusted. * - If stepper drivers sleep, XY homing may be required again before Z homing. */ -//#define Z_SAFE_HOMING +#define Z_SAFE_HOMING #if ENABLED(Z_SAFE_HOMING) #define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing @@ -2296,13 +2299,13 @@ * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes) * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) */ -//#define EEPROM_SETTINGS // Persistent storage with M500 and M501 +#define EEPROM_SETTINGS // Persistent storage with M500 and M501 //#define DISABLE_M503 // Saves ~2700 bytes of flash. Disable for release! #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. #define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load #if ENABLED(EEPROM_SETTINGS) - //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. - //#define EEPROM_INIT_NOW // Init EEPROM on first boot after a new build. + #define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. + #define EEPROM_INIT_NOW // Init EEPROM on first boot after a new build. #endif // @section host @@ -2359,7 +2362,7 @@ * P1 Raise the nozzle always to Z-park height. * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. */ -//#define NOZZLE_PARK_FEATURE +#define NOZZLE_PARK_FEATURE #if ENABLED(NOZZLE_PARK_FEATURE) // Specify a park position as { X, Y, Z_raise } @@ -2565,7 +2568,7 @@ * * :['JAPANESE', 'WESTERN', 'CYRILLIC'] */ -#define DISPLAY_CHARSET_HD44780 JAPANESE +#define DISPLAY_CHARSET_HD44780 WESTERN /** * Info Screen Style (0:Classic, 1:Průša) @@ -2580,7 +2583,7 @@ * SD Card support is disabled by default. If your controller has an SD slot, * you must uncomment the following option or it won't work. */ -//#define SDSUPPORT +#define SDSUPPORT /** * SD CARD: ENABLE CRC @@ -2958,7 +2961,7 @@ // This is RAMPS-compatible using a single 10-pin connector. // (For CR-10 owners who want to replace the Melzi Creality board but retain the display) // -//#define CR10_STOCKDISPLAY +#define CR10_STOCKDISPLAY // // Ender-2 OEM display, a variant of the MKS_MINI_12864 @@ -3357,7 +3360,7 @@ // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency // which is not as annoying as with the hardware PWM. On the other hand, if this frequency // is too low, you should also increment SOFT_PWM_SCALE. -//#define FAN_SOFT_PWM +#define FAN_SOFT_PWM // Incrementing this by 1 will double the software PWM frequency, // affecting heaters, and the fan if FAN_SOFT_PWM is enabled. diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index cbc85283a3..afcd965f54 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -541,7 +541,7 @@ * Hotend Idle Timeout * Prevent filament in the nozzle from charring and causing a critical jam. */ -//#define HOTEND_IDLE_TIMEOUT +#define HOTEND_IDLE_TIMEOUT #if ENABLED(HOTEND_IDLE_TIMEOUT) #define HOTEND_IDLE_TIMEOUT_SEC (5*60) // (seconds) Time without extruder movement to trigger protection #define HOTEND_IDLE_MIN_TRIGGER 180 // (°C) Minimum temperature to enable hotend protection @@ -565,9 +565,9 @@ * The fan turns on automatically whenever any driver is enabled and turns * off (or reduces to idle speed) shortly after drivers are turned off. */ -//#define USE_CONTROLLER_FAN +#define USE_CONTROLLER_FAN #if ENABLED(USE_CONTROLLER_FAN) - //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + #define CONTROLLER_FAN_PIN PC7 // Set a custom pin for the controller fan //#define CONTROLLER_FAN2_PIN -1 // Set a custom pin for second controller fan //#define CONTROLLER_FAN_USE_Z_ONLY // With this option only the Z axis is considered //#define CONTROLLER_FAN_IGNORE_Z // Ignore Z stepper. Useful when stepper timeout is disabled. @@ -913,7 +913,7 @@ //#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (linear=mm, rotational=°) Backoff from endstops after homing //#define XY_COUNTERPART_BACKOFF_MM 0 // (mm) Backoff X after homing Y, and vice-versa -//#define QUICK_HOME // If G28 contains XY do a diagonal move first +#define QUICK_HOME // If G28 contains XY do a diagonal move first //#define HOME_Y_BEFORE_X // If G28 contains XY home Y before X //#define HOME_Z_FIRST // Home Z first. Requires a Z-MIN endstop (not a probe). //#define CODEPENDENT_XY_HOMING // If X/Y can't home without homing Y/X first @@ -1057,11 +1057,11 @@ // // Add the G35 command to read bed corners to help adjust screws. Requires a bed probe. // -//#define ASSISTED_TRAMMING +#define ASSISTED_TRAMMING #if ENABLED(ASSISTED_TRAMMING) // Define from 3 to 9 points to probe. - #define TRAMMING_POINT_XY { { 20, 20 }, { 180, 20 }, { 180, 180 }, { 20, 180 } } + #define TRAMMING_POINT_XY { { 40, 40 }, { 370, 40 }, { 370, 370 }, { 40, 370 } } // Define position names for probe points. #define TRAMMING_POINT_NAME_1 "Front-Left" @@ -1216,7 +1216,7 @@ // Increase the slowdown divisor for larger buffer sizes. #define SLOWDOWN #if ENABLED(SLOWDOWN) - #define SLOWDOWN_DIVISOR 2 + #define SLOWDOWN_DIVISOR 8 #endif /** @@ -1597,7 +1597,7 @@ #if HAS_DISPLAY && EITHER(SDSUPPORT, SET_PROGRESS_MANUALLY) #define SHOW_PROGRESS_PERCENT // Show print progress percentage (doesn't affect progress bar) #define SHOW_ELAPSED_TIME // Display elapsed printing time (prefix 'E') - //#define SHOW_REMAINING_TIME // Display estimated time to completion (prefix 'R') + #define SHOW_REMAINING_TIME // Display estimated time to completion (prefix 'R') #if ENABLED(SET_INTERACTION_TIME) #define SHOW_INTERACTION_TIME // Display time until next user interaction ('C' = filament change) #endif @@ -1737,7 +1737,7 @@ //#define LONG_FILENAME_WRITE_SUPPORT // Create / delete files with long filenames via M28, M30, and Binary Transfer Protocol //#define M20_TIMESTAMP_SUPPORT // Include timestamps by adding the 'T' flag to M20 commands - //#define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu + #define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu //#define SD_ABORT_NO_COOLDOWN // Leave the heaters on after Stop Print (not recommended!) @@ -1838,7 +1838,7 @@ * * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] */ - //#define SDCARD_CONNECTION LCD + #define SDCARD_CONNECTION ONBOARD // Enable if SD detect is rendered useless (e.g., by using an SD extender) //#define NO_SD_DETECT @@ -1939,7 +1939,7 @@ //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames - //#define STATUS_HEAT_PERCENT // Show heating in a progress bar + #define STATUS_HEAT_PERCENT // Show heating in a progress bar //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of flash. // Frivolous Game Options @@ -2208,7 +2208,7 @@ * * See https://marlinfw.org/docs/features/lin_advance.html for full instructions. */ -//#define LIN_ADVANCE +#define LIN_ADVANCE #if ENABLED(LIN_ADVANCE) #if ENABLED(DISTINCT_E_FACTORS) #define ADVANCE_K { 0.22 } // (mm) Compression length per 1mm/s extruder speed, per extruder @@ -2217,7 +2217,7 @@ #endif //#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L. //#define LA_DEBUG // Print debug information to serial during operation. Disable for production use. - //#define ALLOW_LOW_EJERK // Allow a DEFAULT_EJERK value of <10. Recommended for direct drive hotends. + #define ALLOW_LOW_EJERK // Allow a DEFAULT_EJERK value of <10. Recommended for direct drive hotends. //#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz. #endif @@ -2392,7 +2392,7 @@ #endif // G5 Bézier Curve Support with XYZE destination and IJPQ offsets -//#define BEZIER_CURVE_SUPPORT // Requires ~2666 bytes +#define BEZIER_CURVE_SUPPORT // Requires ~2666 bytes #if EITHER(ARC_SUPPORT, BEZIER_CURVE_SUPPORT) //#define CNC_WORKSPACE_PLANES // Allow G2/G3/G5 to operate in XY, ZX, or YZ planes @@ -2824,7 +2824,7 @@ #define INTERPOLATE true #if AXIS_IS_TMC_CONFIG(X) - #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_CURRENT 580 // (mA) RMS current. Multiply by 1.414 for peak current. #define X_CURRENT_HOME X_CURRENT // (mA) RMS current for sensorless homing #define X_MICROSTEPS 16 // 0..256 #define X_RSENSE 0.11 // Multiplied x1000 for TMC26X @@ -2844,7 +2844,7 @@ #endif #if AXIS_IS_TMC_CONFIG(Y) - #define Y_CURRENT 800 + #define Y_CURRENT 580 #define Y_CURRENT_HOME Y_CURRENT #define Y_MICROSTEPS 16 #define Y_RSENSE 0.11 @@ -2864,7 +2864,7 @@ #endif #if AXIS_IS_TMC_CONFIG(Z) - #define Z_CURRENT 800 + #define Z_CURRENT 580 #define Z_CURRENT_HOME Z_CURRENT #define Z_MICROSTEPS 16 #define Z_RSENSE 0.11 @@ -2964,7 +2964,7 @@ #endif #if AXIS_IS_TMC_CONFIG(E0) - #define E0_CURRENT 800 + #define E0_CURRENT 650 #define E0_MICROSTEPS 16 #define E0_RSENSE 0.11 #define E0_CHAIN_POS -1 @@ -3088,28 +3088,28 @@ * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers * on the same serial port, either here or in your board's pins file. */ - //#define X_SLAVE_ADDRESS 0 - //#define Y_SLAVE_ADDRESS 0 - //#define Z_SLAVE_ADDRESS 0 - //#define X2_SLAVE_ADDRESS 0 - //#define Y2_SLAVE_ADDRESS 0 - //#define Z2_SLAVE_ADDRESS 0 - //#define Z3_SLAVE_ADDRESS 0 - //#define Z4_SLAVE_ADDRESS 0 + #define X_SLAVE_ADDRESS 0 + #define Y_SLAVE_ADDRESS 2 + #define Z_SLAVE_ADDRESS 1 + #define X2_SLAVE_ADDRESS 0 + #define Y2_SLAVE_ADDRESS 0 + #define Z2_SLAVE_ADDRESS 0 + #define Z3_SLAVE_ADDRESS 0 + #define Z4_SLAVE_ADDRESS 0 //#define I_SLAVE_ADDRESS 0 //#define J_SLAVE_ADDRESS 0 //#define K_SLAVE_ADDRESS 0 //#define U_SLAVE_ADDRESS 0 //#define V_SLAVE_ADDRESS 0 //#define W_SLAVE_ADDRESS 0 - //#define E0_SLAVE_ADDRESS 0 - //#define E1_SLAVE_ADDRESS 0 - //#define E2_SLAVE_ADDRESS 0 - //#define E3_SLAVE_ADDRESS 0 - //#define E4_SLAVE_ADDRESS 0 - //#define E5_SLAVE_ADDRESS 0 - //#define E6_SLAVE_ADDRESS 0 - //#define E7_SLAVE_ADDRESS 0 + #define E0_SLAVE_ADDRESS 3 + #define E1_SLAVE_ADDRESS 0 + #define E2_SLAVE_ADDRESS 0 + #define E3_SLAVE_ADDRESS 0 + #define E4_SLAVE_ADDRESS 0 + #define E5_SLAVE_ADDRESS 0 + #define E6_SLAVE_ADDRESS 0 + #define E7_SLAVE_ADDRESS 0 // @section tmc/smart @@ -3155,7 +3155,7 @@ * Define your own with: * { , , hysteresis_start[1..8] } */ - #define CHOPPER_TIMING CHOPPER_DEFAULT_12V // All axes (override below) + #define CHOPPER_TIMING CHOPPER_DEFAULT_24V // All axes (override below) //#define CHOPPER_TIMING_X CHOPPER_TIMING // For X Axes (override below) //#define CHOPPER_TIMING_X2 CHOPPER_TIMING_X //#define CHOPPER_TIMING_Y CHOPPER_TIMING // For Y Axes (override below) @@ -3299,7 +3299,7 @@ /** * Step on both rising and falling edge signals (as with a square wave). */ - //#define EDGE_STEPPING + #define EDGE_STEPPING /** * Enable M122 debugging command for TMC stepper drivers. @@ -3763,7 +3763,7 @@ // @section reporting // Extra options for the M114 "Current Position" report -//#define M114_DETAIL // Use 'M114` for details to check planner calculations +#define M114_DETAIL // Use 'M114` for details to check planner calculations //#define M114_REALTIME // Real current position based on forward kinematics //#define M114_LEGACY // M114 used to synchronize on every call. Enable if needed. @@ -3951,7 +3951,7 @@ * Host Prompt Support enables Marlin to use the host for user prompts so * filament runout and other processes can be managed from the host side. */ -//#define HOST_ACTION_COMMANDS +#define HOST_ACTION_COMMANDS #if ENABLED(HOST_ACTION_COMMANDS) //#define HOST_PAUSE_M76 // Tell the host to pause in response to M76 //#define HOST_PROMPT_SUPPORT // Initiate host prompts to get user feedback @@ -3969,7 +3969,7 @@ * * Implement M486 to allow Marlin to skip objects */ -//#define CANCEL_OBJECTS +#define CANCEL_OBJECTS #if ENABLED(CANCEL_OBJECTS) #define CANCEL_OBJECTS_REPORTING // Emit the current object as a status message #endif diff --git a/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_V2_0.h b/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_V2_0.h index 7e6798deaf..b2b023c7ac 100644 --- a/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_V2_0.h +++ b/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_V2_0.h @@ -67,9 +67,10 @@ #define NEOPIXEL_PIN PA8 // LED driving pin #endif -#ifndef PS_ON_PIN - #define PS_ON_PIN PC13 // Power Supply Control -#endif +// DCMINTER:: I'm reusing this pin for HB because PC9 is dead. +//#ifndef PS_ON_PIN +// #define PS_ON_PIN PC13 // Power Supply Control +//#endif #define FAN1_PIN PC7 diff --git a/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_common.h b/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_common.h index 9d85e211f7..e7b48792d0 100644 --- a/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_common.h +++ b/Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_E3_common.h @@ -98,7 +98,8 @@ // Heaters / Fans // #define HEATER_0_PIN PC8 // "HE" -#define HEATER_BED_PIN PC9 // "HB" +//#define HEATER_BED_PIN PC9 // "HB" +#define HEATER_BED_PIN PC13 // Normally this is "PS-ON" but we're using it for the heated bed "HB" as PC9 is dead #ifndef FAN0_PIN #define FAN0_PIN PA8 // "FAN0"